Simplex drain/overflow, flat version
Product information
Simplex drain/overflow, flat version
for standard bathtubs and for bathtubs with
drain hole Ø52
| Year built (from): | 1.9.2019 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-FachkräfteOperators
Consumers
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Intended use
Areas of use
NOTICE!
Risk of damage due to unsuitable liquids
To avoid damaging the drain, only introduce the following liquids:
Typical household wastewater with temperatures up to 95 °C
The pH value must be higher than 4 but lower than 10.
The Simplex drain/overflow is a combined drain and overflow for bathtubs with a 52 mm drain hole.
INFO!
Please note, this model has no odour trap. A separate odour trap must be installed to complete the mounting.
The drain/overflow is suitable for standard bathtubs with the drain on the head end.
Product description
Overview
- 1 valve cone
- 2 fixing screw
- 3 valve top
- 4 Sealing
- 5 Sealing
- 6 drain unit with odour trap
- 7 Bowden cable
- 8 Flexible overflow pipe
- 9 overflow unit
- 10 profile seal
- 11 fixing flange
- 12 rotatable rosette
Technical data
Drainage capacity (at an accumulation height of 300 mm) with Viega odour trap |
|---|
Overflow capacity (at an accumulation height of 60 mm) with Viega odour trap |
Diameter of bathtub drain hole |
Length of Bowden cable |
Length / height |
Dimensions and installation depth |
Handling
Assembly information
Mounting conditions
The following requirements exist for the mounting of the drain / overflow:
The bathtub is installed.
The drainage line is installed all the way to the bathtub.
The underside of the bathtub is accessible.
Installation dimensions
Required tools and materials
Tool
The following tools are required for mounting:
socket spanner (size 14)
fine-toothed saw
flat-blade screwdriver
Material
The following material must be purchased separately and must be available during mounting:
Odour trap
Assembly
Mounting overflow
Proceed as follows to the mounting of the overflow:
-
Fit the profile seal in the overflow unit.
-
Hold the overflow unit on the overflow opening of the bathtub from the outside.
-
Screw the fixing flange into the overflow unit by hand.
Align and fit the rotatable rosette.
NOTICE!Only turn the fixing flange by hand. Pliers or other tools may damage the fixing flange.
-
Shorten the overflow pipe and also the connection pipe on the overflow unit if required.
-
Push the overflow pipe onto the overflow unit.
Mounting the drain
Proceed as follows to mount the drain:
-
Place the profile seal in the recess of the drain unit.
-
Mount the drain unit with profile seal on the drain hole of the bathtub from below.
-
Insert the second seal above the bottom of the bath tub.
-
Fit the valve top in the drain hole.
-
Place the fixing screw in the drain unit and tighten with a socket spanner (size 14) or a Viega mounting aid.
-
Push the union nut, sliding ring and seal onto the bottom end of the overflow pipe.
-
Place the overflow pipe in the drain unit and screw together.
Maintain the insertion depth of at least 15 mm.
Connecting the wastewater system
The drain unit must be connected to an external odour trap as there is no odour trap integrated into the drain fitting.
The drain unit is equipped with a vertical 1½ inch threaded connection for the connection.
Proceed as follows to connect the drain fitting to the wastewater system:
Requirements:
The overflow and drain units are installed on the bathtub.
The connection between overflow and drain has been made.
-
Screw the drain unit together with the on-site odour trap at the threaded connection.
Screw the drain unit together with the on-site odour trap at the connection pipe.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.